Victron Energy Skylla-i 24/100(1+1) 230V – SKI024100000


  Share
Guaranteed Safe CheckoutTrust

£1,607.76

The Skylla-i 24/100 is a modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air.

 

Features of the Skylla-i 24/100

Synchronised parallel operation
Several chargers can be synchronised with the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables. Note: Two output and three output chargers cannot be paralleled with each other.

 

The right amount of charge for a lead-acid battery: variable absorption time
When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.

 

Preventing damage due to excessive gassing: the BatterySafe mode
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-i will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.

 

Less maintenance and aging when the battery is not in use: the Storage mode
The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (26,4V for 24V battery) to minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to refresh the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.

 

To increase battery life: temperature compensation
Every Skylla-i comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations of battery temperature are expected.

 

Battery voltage sense
In order to compensate for voltage loss due to cable resistance, the Skylla-i is provided with a voltage sense facility so that the battery always receives the correct charge voltage.

 

Suitable for AC and DC supply (AC-DC and DC-DC operation)
The chargers also accept a DC supply.

 

Use as a power supply
As a result of the perfectly stabilized output voltage, the Skylla-i 24/100 can be used as a power supply if batteries or large buffer capacitors are not available.

 

Li-Ion (LiFePO4) ready
Simple charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively complete control of voltage and current can be achieved by connecting to the galvanically isolated CAN bus port.

 

Learn more about batteries and battery charging

To learn more about batteries and charging batteries (including the pros and cons of multi-bank charging and intelligent charging), please refer to Electricity on Board.

 

The Skylla-i Control panel provides remote control and monitoring of the charge process with LED status indication. In addition, the remote panel also offers input current adjustment that can be used to limit the input current and thus the power drawn from the AC supply. This is particularly useful when operating the charger from limited shore power or small gensets. The panel can also be used to change several battery charging parameters. Several control panels can be connected to one charger or to a set of synchronised and parallel connected chargers.

 

Want to improve battery charging? Why not take a look at the Victron Energy Battery Sense which measures voltage at the battery bank terminals, errors arising from voltage-loss due to cable resistance are avoided – guaranteeing the correct charge-voltage.

Brand

Victron Energy

Manufacturer Part Number

SKI024100000

GTIN

8.72E+12

Voltage

24V

Charge Current

100A

Input Voltage

230V

Number of Outputs

1+1

Protection Category

IP21

Bluetooth Enabled

No

Dimensions

H405 x W250 x D150mm

Weight

7Kg

Warranty

5 Years

Country of Manufacture

Malaysia

My Cart
Wishlist
Categories